The new generation in “Power Wizard” Control Panels

It is worth remembering that the LPC2 analog Panel series that provides a power range of 10Kva to 20Kva was replaced by the new series called Power Wizard; for this power range the “Power Wizard 1” line, also known as DCP1 is used. This is a very simple and practical digital control panel; it has a digital display in which the electrical and mechanical parameters of the power plant are clearly visualized. This Power Wizard 1 Panel or DCP1 has been thoroughly tested in severe operational conditions (weather, external agents, salt, bangs, etc.) and as the obtained results were excellent, it is considered ideal for its use in Telecommunications. FG Wilson recommends it with an absolute warranty of safety and efficiency. The achievements were so good that the Power Wizard or DCP1 line will soon replace the excellent Series 2001 Control Panel. Additionally, there is the Power Wizard 2 and 3 or DCP2 and DCP3 that will replace the very efficient Panel Access 4000. The best one is the Power Wizard 4 or DCP4 that will replace the whole 6000 series of Control Panels used in parallel and synchronizing with other Power Plants, or with the Commercial Network or with both at the same time. Through the links you can access more information and characteristics of the Power Wizard.

http://www.sertec.com.py/telergia/telergia/informaciones/new_panel.html

http://www.sertec.com.py/telergia/telergia/informaciones/power_wizard1.html

Comments

[Akovoyon Samuel]

Sir,I work with J.M.G.generator company in Nigeria,In assembly department.Please i will like to know more on power wizard because i assemble F.G WILSON generators thanks in advance.

[Sofola Olatunde]

i am staff of jmg limited in nigeria. i want to know more about power wizard panel.

[Richard Lingard]

I operate a generator with power wizard control unit fitted. I have a maintenance alarm indicated which will not clear. Can you advise the codes for access to reset this fault.

Thanks

Richard Lingard

[Agok]

I would like to know how to make PowerWizar start the generator remotely through a time switch, thanks

[Eng. Ibrahim Rahman]

Dear Sir
I need operation manual and wiring digram for this control panel or any other catalogs u can give and You Know its helpful
its installed with Perkins engine 4006 series and I will be very Thankful

[Rabih Abourahal]

Dear Sir

I have tow power wizard 2.0 control panel installed on two generators.
I want to integrate with these panels via MODBUS RTU(RS485),
Please, can you send the REGISTERS LIST of this panel.
Please advise.
Thanks.

[Petr]

I am developing a program control panel power wizard 2.
can you send the REGISTERS LIST of this panel ?

[samson waithaka]

Hey I work with excel engineering Kenya. I have a power wizard 1.0 which displays everything okey,but isn't starting the generator.On dismantling the power wizard, a diode is blown. After replacing with a similar diode, still not starting. Where is the remedy?

[Dudu]

powerwizard 2.0
can you send the REGISTERS LIST of this panel ?
thank you

[David]

Can you Please send MODBUS registers thank you

[ROB STAHL]

I HAVE A NEW PANEL I HAVE HAD FOR SOME TIME,I AM WANTING TO INSTALL ON A GENERATOR I PUT TOGETHER, CAN YOU TELL ME IF IT IS A 1.0, 2.0, OR 3.0 BY THE S/N 2957B752HP OR BY THE AMOUNT OF PINS (61PINS) ALSO IS THERE A LEVEL 3 PASSWORD IN NEW PANELS OR CAN I PUT IN MY OWN WITHOUT THE USE OF A EST. IF NOT WHAT KIND OF BASIC EST TOOL WILL I NEED TO AQUIRE TO DO THE JOB? THANK YOU

[Rajesh K]

Please help me to know whether powerwizard 1.0 can be used to synchronise four generators?(all four generators have same panel)if not what is the way out?